Spectrum MultiGrip F240 is a fast drying, high-build slip resistant coating system that can be used for a wide range of area applications. Ideal for use on hard surfaces such as roads, car parks, distribution centres, airports and docks. MultiGrip F240 is a toluene free paint, meaning it is more environmentally friendly than other products, such as chlorinated rubber. MultiGrip F240 should be applied using spray methods, supplied in 20kg tins and available in a choice of colours. MultiGrip F240 comes packaged in the innovative EnviraPac liner system, which allows maximum usage of product, recycling of clean metal tins and most importantly considerable reduction of waste costs.
FIND OUT MORE ABOUT ENVIRAPAC:
Features and Benefits:
Fast drying, for rapid return to service
Textured surface achieving a SRV in excess of 55
High solids for excellent opacity
EnviraPac liner to allow recycling of tin & reduce disposal costs"
Surface preparation: The application surface should be sound and clean, free from grease, oil, rust, scale, dirt, or any other soiling that might affect adhesion or performance. In any case, but especially in the case of overcoating existing line markings, it is further recommended that test areas be coated to ensure good adhesion and/or compatibility with the substrate.
Asphalt – weathered - It is recommended that asphalt and other similar surfaces be allowed to through harden for up to 6 months before painting. Test trials should be carried out in the first instance on a small area.
Concrete & other cementitious surfaces – including powerfloat, tamped or brushed concrete, monoblocks & pavers – Ensure surface is sound, clean and free from laitance – we recommend a preparation method suitable for the specific location and surface is carried out before application of product, to ensure surface is properly prepared back to clean and sound substrate.
Examples of preparation methods that may be suitable are captive shot blasting, diamond grinding, scabbling or planing. It is critical that utmost attention is paid to cleanliness and good workmanship, whatever preparation method is used, as the presence of any loose material, dust, soiling or previous coatings are likely to reduce adhesion of new coatings.
New concrete should be left to harden before coating, as the curing process and residual moisture content can lead to product delamination if coated too early.
Asphalt & tarmacadam - no primer required
Concrete, pavers & monoblocks - use Meon Spectrum UniPrime
Stir thoroughly before use.
Thinning: This product is supplied ready to use and need not be thinned. If thinning is required, Meon SF Thinners may be used, up to 20% by volume.
we highly recommend the use of airless spray equipment as this will provide the best finish. Take care to apply evenly and do not over-apply as this will severely inhibit the curing process and is likely to result in damage to bituminous surfaces due to excessive exposure to solvents. It is particularly important to exercise the utmost care when coating any bituminous surface – we recommend the application of a light mist coat first, allowing time for full cure of mist coat, then followed with a full coat. We recommend the use of masking tape to protect against overspray & provide neat edge finish where required.
Airless spray – use 0.031” tip or larger, with spray angle to suit application. Do not use a lining tip (such as a Graco LL5) as this is likely to leave “tramline” effect.
Do not apply when the air or surface temperature is below 5°C or less than 3°C above dew point, or if this is likely to occur during the curing period.
Do not apply when there is rain, mist, fog, or snow imminent; when humidity is high or the surface is wet with condensation or likely to be during the drying period.
Touch dry: 5 minutes @ 15⁰C.
Walk on time: 10 minutes @ 15⁰C.
Traffic time: 20 minutes @ 15⁰C.
Full cure: 60 minutes @ 15°C
Recoat: 1-2 hours @ 15⁰C."
| 26/7/2017 15:23
Zebra Crossing removal by Steve
As part of a recent scheme we were required to remove an existing Zebra Crossing . The job had to be done on day one and quickly.
Using roller applied Spectrum Multi-Grip F240 was a perfect choice for us. The 1st running lane was open within 30 minutes and 2 way traffic running within 1 hour.
Great product and one we would recommend to anyone.